Hoop Stress Calculator

Everyday hoop stress problems come down to one relationship between shell diameter (d), efficiency of the circumferential joint (η), efficiency of the circumferential joint (ηc), efficiency of the longitudinal riveted joint (ηt), length of the shell (l), poisson’s ratio (μ), internal pressure (p), thickness of the shell (t) and young’s modulus (e). This calculator turns those numbers into maximum out of plane shear stress (σs2), change in diameter (δd) and change in volume (δv), with the working shown so you can check the result rather than simply trust it.

What Is the Hoop Stress Calculator?

This hoop stress calculator is for the kind of problem where you know the physical quantities but not the number you need. It turns shell diameter (d), efficiency of the circumferential joint (η), efficiency of the circumferential joint (ηc), efficiency of the longitudinal riveted joint (ηt), length of the shell (l), poisson's ratio (μ), internal pressure (p), thickness of the shell (t) and young's modulus (e) into maximum out of plane shear stress (σs2), change in diameter (δd) and change in volume (δv).

Physics calculations go wrong in predictable ways, usually through mixing units or dropping a digit. Work through the result one step at a time and check that the figures are the size you would expect at each stage.

How the Hoop Stress Physics Works

The relationship is applied step by step, and each step is a standard piece of physics rather than a single opaque formula. That means you can check the intermediate values against what the theory predicts, which is usually faster than checking only the final answer.

Keep every value in the same unit system throughout the calculation. Mixing metres and feet part way through is the single most common reason a correct formula gives a wrong answer.

Units, Assumptions and the Limits of the Model

The calculation assumes ideal conditions: no air resistance, no heat loss, and dimensions that do not change while you work. Those assumptions are reasonable for most classroom and engineering estimates, and unreasonable for anything more precise.

Where a value is a rate, it has to be quoted for the same period as everything else. A per-hour figure cannot be combined with a per-day figure without converting one of them first.

A Worked Example

Working through an example, with shell diameter (d) set to 10, efficiency of the circumferential joint (η) set to 5, efficiency of the circumferential joint (ηc) set to 2, the calculator returns shell radius (r) of 5, and thickness to diameter ratio (t/d) of 10, and hoop stress (σh) of 0.001. Substitute your own figures and the same steps produce the same kind of answer.

Frequently Asked Questions

What do I need to work out maximum out of plane shear stress (σs2)?

Enter shell diameter (d), efficiency of the circumferential joint (η), efficiency of the circumferential joint (ηc), efficiency of the longitudinal riveted joint (ηt), length of the shell (l), poisson's ratio (μ), internal pressure (p), thickness of the shell (t) and young's modulus (e). The calculator then works through the relationship and reports maximum out of plane shear stress (σs2), change in diameter (δd) and change in volume (δv).

What does the hoop stress actually calculate?

It takes shell diameter (d), efficiency of the circumferential joint (η), efficiency of the circumferential joint (ηc), efficiency of the longitudinal riveted joint (ηt), length of the shell (l), poisson's ratio (μ), internal pressure (p), thickness of the shell (t) and young's modulus (e) and converts them into maximum out of plane shear stress (σs2), change in diameter (δd) and change in volume (δv) using the standard relationship for this problem. Each step is applied in turn, so every output is traceable back to the numbers you typed in.

How should I enter shell diameter (d)?

Use the value you actually have, in the unit shown next to the field. Enter every value in the same unit system. The calculator assumes the figures you supply are consistent, so it cannot correct a mistake that happens before the calculation starts.

Can I use this for a quick estimate as well as a precise answer?

Yes. The calculator is built for quick checks, so round your inputs to a sensible number of significant figures and the result will be just as useful. If you need more precision, keep the same method and add digits to the inputs rather than adjusting the method itself.

Why does a small change in one value move the answer so much?

That happens when an output depends on a ratio, because dividing by a small number magnifies any change in it. Check the units first, then check whether the value you entered is in the range the relationship was designed for.

Scroll to Top